Instant Film (Instax)
Print on Fujifilm Instax Link printers by Bluetooth or through the print server.
Fujifilm Instax Link printer
Instax Link printers print instant film straight from the device by Bluetooth, without the print server. Set it up in the print server window, under Fujifilm Instax Link printer (Beta). For the Link Wide and Link Wide 2, the official Fujifilm Windows driver on the print server is recommended instead.
Supported printers
Instax Mini Link, Mini Link 2, Mini Link 3, Square Link, Link Wide and Link Wide 2. Photos are fitted to the film: Mini 3:4, Square 1:1, Wide 3:2.
Supported apps
The iPhone/iPad, Android and Windows apps, by Bluetooth. It is not available in a web browser.
Set up the Instax printer
- 1
Free the printer
Turn the printer on and keep it close to the device. Close the Instax app on other phones or turn their Bluetooth off: the printer connects to one device at a time.
- 2
Turn on Instax printing
Open the print server window and switch on Fujifilm Instax Link printer. Allow Bluetooth when the app asks.
- 3
Connect the printer
Tap Connect printer. If several printers are found, choose yours (its name starts with INSTAX-). The Windows app picks it by itself.
- 4
Check the model
Leave Printer model on Detect automatically, or choose your model if prints are cropped wrongly. Tap Check status to see the model, battery and film left.
- 5
Print a test photo
Tap Test print. From then on the photo booth prints to the Instax, one print at a time, and reconnects to it by itself.
Backup and Mini Link 3
Turn on Use the print server if the Instax fails to send the photo to the print server when the Instax is off or out of film. If a Mini Link 3 does not print, set Mini Link 3 upload block size to 1808 (default 900). If the printer light turns orange, switch the printer off and on again. If a Link Wide 2 does not print, set Link Wide 2 upload block size to 1808.
Instax Link Wide and Link Wide 2 on the print server (recommended)
Fujifilm makes an official Windows printer driver for the instax Link WIDE printers, and it works for both the Link Wide and the Link Wide 2. Installed on the print server PC, the Instax becomes a normal Windows printer and the print server prints to it like any other printer. This is the recommended way to print to a Link Wide or Link Wide 2: the driver is official, while the Bluetooth option in the app is Beta.
Official driver
It comes from Fujifilm, so printing does not depend on the app's Beta Bluetooth connection or its upload block size.
Every device can print
iPhone/iPad, Android, Windows and any other device connected to the print server, over Wi-Fi or a cable, sends its photos to the Instax.
Set up the Windows driver
- 1
Install the driver on the print server PC
Download Fujifilm's official instax Link WIDE printer driver for Windows from Fujifilm's instax website and install it on the PC that runs the print server. Add the printer as Fujifilm's instructions describe.
- 2
Free the printer
Turn off Fujifilm Instax Link printer in the app's print server window on every device, and close the Instax app on nearby phones: the printer connects to one device at a time.
- 3
Find it in the print server
Open the print server, go to the Printers tab and tap Refresh. The Instax appears in the list; tap Print test page to check it.
- 4
Choose it for the event
In the event settings, open Enable Printer and under Printer choose the Instax from the print server's printers, not Fujifilm Instax Link (direct via Bluetooth, no print server, Beta).
- 5
Use a 3:2 print layout
Wide film is 3:2. Use a landscape 3:2 print layout and leave the event's margins at 0. In the print server, keep Rotate images to match the paper on and the fit on Fill the page.
- 6
Print a photo
Take a photo in the booth with this event. It comes out of the Instax a few seconds later, and the print server's Print history tab lists each job.
Good to know
Use either the Windows driver or the Bluetooth option for a printer, not both at once. The Bluetooth option (Beta) stays available for the Mini Link, Mini Link 3 and Square Link, and for tablets used without a print server PC.
Common questions
No Instax printer appears in the list.
When the search finds nothing, the app shows No Instax printer found. Work through these: 1. Turn the printer on (the light must be lit) and charge it if the battery is low; it switches itself off after a few idle minutes. 2. Keep it within about 1 metre of the device. 3. Close the Instax app on every other phone or turn their Bluetooth off: the printer only talks to one device at a time. 4. Make sure Bluetooth is on and the app is allowed to use it (Android: Nearby devices permission; iPhone/iPad: Settings → app → Bluetooth). 5. Do not pair the printer in the phone's or Windows' Bluetooth settings; if you did, remove it there. 6. Switch the printer off and on, wait 10 seconds and tap Connect printer again. Instax printing works only in the iPhone/iPad, Android and Windows apps, not in a web browser.
The Instax printer is out of film.
Film left shows a red 0 and printing stops with No film left. 1. Load a new pack of the right film: instax mini for the Mini Links, instax SQUARE for the Square Link, instax WIDE for the Link Wide and Link Wide 2. Only open the back cover when the pack is empty. 2. Close the cover firmly: the printer ejects the black cover sheet. 3. Tap Check status: Film left shows 10 again. Photos that failed while the film was empty went to the print server if Use the print server if the Instax fails is on; otherwise print them again.
The Instax printer light is orange.
An orange or blinking light means the printer is busy or has a problem, and the app shows The Instax printer is busy or stuck (orange light). 1. Wait until the current print has fully come out (about 15 seconds). 2. Check the film: an empty pack or an open cover also turns the light orange. 3. Charge the printer if the battery is low. 4. Switch the printer off and on, wait 10 seconds and tap Check status. 5. If the light stays orange after a restart and a charge, look up the light pattern in Fujifilm's manual for your model or contact Fujifilm support.
The Mini Link 3 connects but does not print.
Check status works, but a test print fails or nothing comes out. 1. Make sure Printer model is Instax Mini Link 3 (choose it if Detect automatically shows Mini Link). 2. Set Mini Link 3 upload block size to 1808 and tap Test print. 3. If it still fails, set it back to 900. 4. Switch the printer off and on before each try. 5. Update the printer's firmware with Fujifilm's instax mini Link app, then close that app so it does not keep the printer connected.
Does the Instax Link Wide 2 work?
Yes. Recommended: install Fujifilm's official instax Link WIDE printer driver on the Windows print server PC and choose that printer for the event; it works for both the Link Wide and the Link Wide 2 (see Instax Link Wide on the print server). Bluetooth (Beta), without a print server PC: 1. Connect it like the other models. 2. Tap Check status: Model should show Instax Link Wide 2. If it shows Instax Link Wide or Unknown, choose Instax Link Wide 2 under Printer model; both print at the same 3:2 size. 3. Use a 3:2 landscape print layout. 4. If a test print fails, set Link Wide 2 upload block size to 1808. Do not use both ways for the same printer at once.