Sticker Printer (PixCut S1)

    Print and cut sticker sheets on the Liene PixCut S1 by Bluetooth, USB or the print server.

    Liene PixCut S1 sticker printer

    The PixCut S1 is driven straight from the device, or (Beta) through the Windows print server. Choose the connection in the printer settings, under Liene PixCut S1 sticker printer.

    Bluetooth

    iPad, iPhone and Android apps, and the Windows/Mac desktop app. Sheets are sent in the background, usually under a minute each.

    USB cable

    Windows/Mac desktop app (about 10 seconds per sheet), M-series iPads with the PixCut driver turned on, and Android tablets with a USB-OTG cable (tap Allow the first time). On Windows, install the WinUSB driver once with Zadig for interfaces 2 and 3 of the printer.

    Print server (Windows, Beta)

    The PixCut is plugged into the print server PC by USB, and every device connected to the print server can print stickers on it. See PixCut through the Windows print server.

    The PixCut S1 section of the printer settings, with the Print test photo button.

    Pair or plug in the printer, then tap Print test photo in the PixCut section.

    PixCut S1 through the Windows print server (Beta)

    The PixCut S1 can also be plugged into the print server PC by USB. Every device connected to the print server (iPhone/iPad, Android or Windows, over Wi-Fi or a cable) can then print stickers on it. Liene makes no Windows printer driver for the PixCut, so the print server talks to the printer directly over USB. This needs the WinUSB driver, installed once with the free Zadig tool. This option is Beta: it is still being tested on real printers.

    Every device, one printer

    Phones and tablets send the finished sticker sheet to the print server, which sends it to the PixCut in about 10 seconds. One sheet is sent at a time.

    iPad on its own: use Bluetooth

    For an iPad without a print server PC, Bluetooth needs no driver and no extra setup: choose Bluetooth in the PixCut settings instead.

    Set up the PixCut on the print server

    1. 1

      Install the print server

      Install the Windows Print Server (version 1.5 or later) from the Resources page and connect your devices to it as usual.

    2. 2

      Install the WinUSB driver once with Zadig

      Plug in the PixCut and turn it on. Download Zadig from zadig.akeo.ie and open it, then choose Options → List All Devices. Pick the PixCut entry ending in (Interface 2) and check that the USB ID reads 302C 3101 02. Choose WinUSB as the driver and click Replace Driver (or Install Driver). Repeat for (Interface 3), whose USB ID ends in 03.

    3. 3

      Close the Liene app

      Quit the Liene Photo app on this PC, including from the notification area. Only one program can use the printer at a time.

    4. 4

      Plug in the PixCut

      Plug the printer straight into the PC, not into a hub, and turn it on. On the print server's Server tab, the PixCut line shows PixCut: connected.

    5. 5

      Choose Print server in the app

      In the app, open the printer settings, switch on Liene PixCut S1 sticker printer and set Connection to Print server (Windows). The panel shows the PixCut status reported by the print server.

    6. 6

      Print a test sticker

      Tap Test print. The sheet prints and cuts on the PixCut. Tap Check status to see paper or cartridge problems.

    Good to know

    After the Zadig step, the Liene Photo app can no longer reach the printer over USB on this PC until the original driver is restored (see the questions below). Bluetooth printing is not affected. Paper and cartridge alerts appear in the app just as with Bluetooth and USB.

    Common questions

    The print server shows "PixCut: not found".

    1. Check that the PixCut is on and plugged straight into the print server PC. 2. If the Server tab shows PixCut: needs the WinUSB driver, run the Zadig step again for (Interface 2) and (Interface 3): both are needed. 3. If it shows PixCut: used by another program, quit the Liene Photo app (also from the notification area) and any other program using the printer, then click Check again. 4. Unplug the printer, wait 5 seconds and plug it in again. See PixCut through the Windows print server.

    The Liene app no longer sees the PixCut.

    Zadig replaced the printer's USB driver with WinUSB, so the Liene Photo app cannot reach it over USB. To restore the original driver: 1. Close the print server. 2. Open Device Manager and find the PixCut entries under Universal Serial Bus devices. 3. Right-click each one → Uninstall device, tick Attempt to remove the driver for this device if it is shown, and confirm. 4. Unplug the printer and plug it in again: Windows installs the original driver. Bluetooth in the Liene app is not affected.

    1